1153.PDF
(
46 KB
)
Pobierz
MAX712 Linear-Mode Evaluation Kit
_______________General Description
The Linear-Mode evaluation kit (EV kit) is a complete
battery charger for Nickel Metal Hydride (NiMH) and
“fast-charge” Nickel-Cadmium (NiCd) cells. The num-
ber of cells, charging current, and maximum charging
time are selected by setting DIP switches. The board is
easily tailored for the optimum charging parameters of
a variety of “fast-charge” batteries, and can be used
with either the MAX712 or MAX713.
The MAX712 EV kit automatically initiates the high-cur-
rent, fast-charge cycle when batteries are installed into
the holder. An LED indicates that the fast-charge
sequence is in progress. Fast charge terminates when
the maximum charging time has lapsed, or the circuit
detects that full charge has been achieved, and/or if the
temperature is beyond acceptable limits.
Thermistors are provided for optionally monitoring the
battery temperature. The fast-charge cycle can be inhib-
ited if the battery is too cold, or terminated if the battery
temperature rises beyond limits. The temperature thresh-
olds are adjustable using potentiometers on the board.
____________________________Features
o
Selectable Number of Cells (1 to 16)
o
Selectable Maximum Fast-Charging Timeout
o
Selectable Charging Current
o
Battery Temperature Monitoring Capabilities
o
Adjustable Temperature Limits
o
LED Indication of Fast-Charge Cycle
o
On-Board Battery Holder for 1 or 2 AA Cells
o
Voltage-Slope Fast-Charge Termination
Evaluates: MAX712/MAX713
______________Ordering Information
PART
MAX712EVKIT-DIP
TEMP. RANGE
0°C to +70°C
BOARD TYPE
Through-Hole
______________________________________________________________Component List
DESIGNATION
C1, C3
C2, C7
C4
C5, C6
C7
D1
J1
LED1, LED2
Q1
R1
R3, R5
R4
R6, R7
R8
R9–R11
R12–R15
R16
R17
QTY
2
2
1
2
1
1
1
2
1
1
2
1
2
1
3
4
1
1
DESCRIPTION
10µF, 35V electrolytic capacitors
1.0µF ceramic capacitors
0.01µF ceramic capacitor
0.022µF ceramic capacitors
0.01µF ceramic capacitor
1N4001 diode
3-pin jumper header
Red LEDs
2N6109 PNP power transistor
200Ω, 5% resistor
470Ω, 5% resistors
150Ω, 5% resistor
10kΩ multiturn potentiometers
20kΩ multiturn potentiometer
1kΩ, 5% resistors
1.0kΩ, 5% 1/2W resistors
2.0Ω, 5% 1/2W resistor
3.9Ω, 5% 1/2W resistor
IC1
None
None
None
None
None
None
None
None
None
1
1
2
1
1
1
1
4
1
1
TR1–TR3
3
DESIGNATION
R18
R19
R20
SWA
SWB
QTY
1
1
1
1
1
DESCRIPTION
8.2Ω, 5% 1/2W resistor
16Ω, 5% 1/2W resistor
330Ω, 5% 1/2W resistor
12-position DIP switch
8-position DIP switch
10kΩ at +25°C thermistors.
Alpha thermistor part number
13A1002 NTC. Phone
(800) 235-5445.
MAX712CPE
16-pin IC socket
Battery holder for two AA cells
2-pin power connector
3-pin power connector
Shunt for J1
4.0" x 4.0" PC board
Rubber feet
MAX712/MAX713 data sheet
MAX712/MAX713 EV kit manual
1
________________________________________________________________
Maxim Integrated Products
Call toll free 1-800-998-8800 for free samples or literature.
MAX712 Linear-Mode Evaluation Kit
Evaluates: MAX712/MAX713
___________________Quick Reference
The MAX712 evaluation kit (EV kit) is ready to charge
two fast-charging AA NimH cells. The switches and
voltages are set at the factory per Tables 5, 6, and 7.
Simply connect a 7V, 1A supply to the VIN power con-
nector and insert two discharged AA NimH cells.
The MAX712 EV kit can be used to evaluate the
MAX713 for charging NiCd batteries by replacing the
MAX712CPE (included in this kit) with a MAX713CPE.
NOTE:
The EV kit is intended for use with cells capable of
the high currents needed for fast-charging cycles.
The proper charging current and period will depend
on the exact type of battery being charged. Be
sure the kit is configured properly.
Check the default values and switch settings
before applying power to the board. Refer to Tables
6 and 7 for the default settings. To ensure the
board is operating, verify Table 8’s voltages after
power is applied and without a battery inserted.
The power-indicating LED will light as soon as power
is applied. The voltage across the battery terminals,
BATT+ and BATT-, will be two times the voltage on the
VLIMIT pin. When batteries are inserted into the hold-
er, the MAX712/MAX713 start a fast-charge cycle and
light the charge-indicator LED. The default battery
current is set to 250mA during the fast-charge cycle.
Battery voltage can be monitored by connecting a
voltmeter across the BATT+ and BATT- terminals.
ate topping-off current, and a low trickle current.
Neither the MAX712 nor the MAX713 is intended to
charge this type of NiMH battery.
Input Source
The MAX712/MAX713 require an input 1.5V greater than
the maximum charging voltage, with a 6V minimum.
Because of Q1’s power-dissipation limits, the EV kit
operates ideally with the input voltage set to 7V. This
allows charging currents up to 1A while dissipating less
than 5W from Q1. Higher input voltages and charging
currents can be used if Q1’s power dissipation is
reduced or a sufficient heat sink is attached to Q1.
For input voltages greater than 11V, it may be necessary
to change R1’s value, which must allow greater than
5mA for the MAX712/MAX713 plus approximately 16mA
for drive current to the LED indicators. See the
Powering
the MAX712/MAX713
section of the data sheet for more
information about R1 selection. For the EV kit, the input
source must be capable of handling the charging cur-
rent plus 25mA. Connect the source to a 2-terminal con-
nector on the board marked +VIN and GND.
When choosing an adapter for use with the
MAX712/MAX713, make sure that the lowest wall-cube
voltage level during fast charge and full load is at least
1.5V higher than the maximum battery voltage while
being fast charged. Typically, the voltage on the battery
pack is higher during a fast-charge cycle than while in
trickle charge or while supplying a load. The voltage
across some battery packs may approach 1.9V/cell.
The 1.5V of overhead is needed to allow for worst-case
voltage drops across the pass transistor (Q1), the
diode (D1), and the sense resistor (R
SENSE
). This mini-
mum input voltage requirement is critical, because its
violation may inhibit proper termination of the fast-
charge cycle. A safe rule of thumb is to choose a
source that has a minimum input voltage = 1.5V +
(1.9V x the maximum number of cells to be charged).
When the input voltage at DC IN drops below the 1.5V
+ (1.9V x number of cells), the part will oscillate
between fast charge and trickle charge and may never
completely terminate fast charge.
_______________Detailed Description
The MAX712 EV kit provides the regulated high cur-
rents used for recharging the increasingly popular
“fast-charge” batteries. The kit is shipped ready to
charge two AA NimH cells. Be sure the programmed
current does not exceed the maximum charging cur-
rent of the batteries to be charged. Tables 1–5 list
the different user options available on the EV kit.
Tables 6, 7, and 8 list the levels preset at the factory
for the various charging parameters.
Choosing Between the MAX712
and the MAX713
The MAX712 is intended to charge only NiMH batter-
ies because it uses a zero delta voltage full-charge
detection scheme. The MAX713 can be used to
charge either NiCd or NiMH batteries because its
2.5mV-per-cell resolution allows it to detect the very
slight peak in the NiMH charge characteristic. Some
NiMH batteries require three different current levels
when charging: an initial high current, an intermedi-
2
Battery Connection
The battery connects acros s t he bat tery hi gh
(B A TT+ ) and bat tery low (BATT-) pins of t he
MAX712/MAX713. The pins connect to the battery
holder and the 3-pin terminal block on the board.
The battery holder charges one or two AA cells,
depending on J1’s position. Jumper J1 should be
placed across pins 2 and 3 for a single cell and
across 1 and 2 for two cells.
_______________________________________________________________________________________
MAX712 Linear-Mode Evaluation Kit
External batteries can be connected across the
BATT+ and BATT- pins of the 3-pin output connector.
The third terminal is connected to the input ground
(GND). The GND pin is used when driving external
loads while charging.
When using external batteries, jumper J1 has no
effect. Remove all batteries from holder before
installing external batteries.
Whenever changing the number of cells to be charged,
PGM0 and PGM1 need to be adjusted accordingly.
Attempting to charge more or fewer cells than the num-
ber programmed may disable the voltage-slope fast-
charge termination circuitry. The internal ADC’s input
voltage range is limited to between 1.4V and 1.9V and
is equal to the voltage across the battery divided by the
number of cells programmed. When the ADC’s input
voltage falls out of its specified range, the voltage-
slope termination circuitry is disabled.
The MAX712/MAX713 multiply the input voltage on the
VLIMIT pin by the programmed number of cells to be
charged. This becomes the maximum output voltage
of the MAX712/MAX713. V
LIMIT
should be set between
1.9V and 2.5V. If V
LIMIT
is set below the maximum cell
voltage, proper termination of fast-charge cycle may
not occur. Cell voltage can approach 1.9V/cell, under
fast charge, in some battery packs. Tie V
LIMIT
to V
REF
for normal operation.
PGM2 and PGM3 are used in combination to select the
maximum charging time (timeout) and the time interval
between samples taken by the internal ADC. The fast-
charge cycle terminates regardless of the battery level
when the timeout period expires. Timeout intervals
between 22 and 264 minutes can be selected.
The interval between the ADC samples varies with the
timeout selection. If the voltage-slope fast-charge ter-
mination circuitry is enabled, the readings are also
compared to the previous reading. Fast charge ceases
if the delta is not more positive than zero for the
MAX712 or -2.5mV for the MAX713.
PGM3 also sets the sense voltage for the trickle-charge
phase.
The inputs to the programming pins (PGM0-PGM3) are
set with the 12-position DIP switch (SWA). For exam-
ple, to connect PGM2 to BATT-, first open (OFF) S7,
S8, and S9, then close (ON) S8.
Evaluates: MAX712/MAX713
Sense-Resistor Selection
The charging rate is determined by the value of the
sense resistor connected between BATT- and GND.
The 8-position DIP switch (SWB) can select several dif-
ferent values. For fast charge, the sense voltage is
fixed at 250mV and the resistor value is selected for the
desired current. The sense resistor also sets the trickle
current. Choose R
SENSE
using the following formula:
R
SENSE
= 0.25V/I
FAST
See the MAX712/MAX713 data sheet for complete
information on setting the currents for fast (I
FAST
) and
trickle charging.
Table 1. Switch-Selected Sense-Resistor
Values
SWITCH
1
2
3
4
5
6
7
8
RESISTOR (Ω)
1.0
1.0
1.0
1.0
2.0
3.9
8.2
16.0
Note:
A 330Ω resistor (R20) is paralleled across the
sense resistor to prevent the open-sense line condition.
An unused resistor position (R21) is also provided so
the user can mount a selected value.
Table 2. Programming Pin Input Selection
INPUT
Open
REF
BATT-
V+
PGM0
–
S1
S2
S3
PGM1
–
S4
S5
S6
PGM2
–
S7
S8
S9
PGM3
–
S10
S11
S12
Mode Selection
Four pins on the MAX712/MAX713 are used to select
the number of cells, maximum charging time, and inter-
val between battery voltage measurements. PGM0 and
PGM1 are used in combination to indicate the number
of cells in the battery.
_______________________________________________________________________________________
3
MAX712 Linear-Mode Evaluation Kit
Evaluates: MAX712/MAX713
How to Use the Thermistors
Thermistors TR1 and TR2 detect when the battery
temperature exceeds the ambient temperature. With
two of the same type of thermistors, as long as the
battery temperature is the same as the ambient tem-
perature, the voltage at TEMP will be 1.0V. At +25°C
ambient temperature and +35°C battery temperature,
TR2 has 10kΩ resistance and TR1 has 5.2kΩ resis-
tance (see the graph labeled “Alpha Thermistor Part
No. 13A1002” in the
Typical Operating Characteristics
of the data sheet); thus TEMP equals 1.3V. Fast charge
terminates once TEMP exceeds THI. Adjust the voltage
on THI to set the over-temperature trip point.
Thermistor TR3 detects when the temperature is too
cold to fast charge the battery. Before charging has
started, TEMP will equal 1.0V since the battery temper-
ature will be the same as ambient. At 0°C, TR3 has
33kΩ resistance. Setting R8 to 33kΩ inhibits fast
charging for temperatures below 0°C, since TR3’s
resistance will be greater than 33kΩ at temperatures
below 0°C and thus the voltage at TLO will be greater
than 1.0V.
If the MAX712/MAX713’s temperature detection fea-
tures are not used, do not forget to disable the temper-
ature comparators by tying THI = V+ and TLO = BATT-.
TEMP should be connected to a voltage divider con-
sisting of a 68kΩ resistor to V
REF
, and a 22kΩ resistor
to BATT-. Refer to the
Typical Operating Circuit
of the
MAX712/MAX713 data sheet.
Table 3. Programming the Timing Functions
Timeout
(min)
22
22
33
33
45
45
66
66
90
90
132
132
180
180
264
264
Sample
Interval
(sec)
21
21
21
21
42
42
42
42
84
84
84
84
168
168
168
168
Slope
Limit
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
PGM2
Connection
Open
REF
V+
BATT-
Open
REF
V+
BATT-
Open
REF
V+
BATT-
Open
REF
V+
BATT-
PGM3
Connection
V+
V+
V+
V+
Open
Open
Open
Open
REF
REF
REF
REF
BATT-
BATT-
BATT-
BATT-
S7–S9
–
S7
S9
S8
–
S7
S9
S8
–
S7
S9
S8
–
S7
S9
S8
S10–S12
S12
S12
S12
S12
–
–
–
–
S10
S10
S10
S10
S11
S11
S11
S11
Sense Voltage
in Trickle
(mV)
4
4
4
4
8
8
8
8
16
16
16
16
32
32
32
32
4
_______________________________________________________________________________________
MAX712 Linear-Mode Evaluation Kit
Table 4. Programming the Number of Cells
Number
of Cells
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PGM0
Connection
V+
V+
V+
V+
Open
Open
Open
Open
REF
REF
REF
REF
BATT-
BATT-
BATT-
BATT-
PGM1
Connection
V+
Open
REF
BATT-
V+
Open
REF
BATT-
V+
Open
REF
BATT-
V+
Open
REF
BATT-
S1–S3
S3
S3
S3
S3
Open
Open
Open
Open
S1
S1
S1
S1
S2
S2
S2
S2
S4–S6
S6
–
S4
S5
S6
–
S4
S5
S6
–
S4
S5
S6
–
S4
S5
Evaluates: MAX712/MAX713
Table 7. Evaluation Board Switch Settings
For Charging Two NiCd AA Cells
(Pre-Shipment Settings)
Switch A (SWA)
PGM0 = V+,
PGM1 = Open
PGM2 = BATT–,
PGM3 = BATT–
Switch B (SWB)
S1
Jumper J1
J1
1&2
Set for charging two
AA batteries
R
SENSE
= 1.0Ω
Fast-charge current =
250mA
On Switches
(all others off)
S3, –
Function
Indicates two cells
264min timeout,
168sec ADC
interval, slope limit on
S8, S11
Table 5. Trickle-Charge Sense-Voltage
Selection
PGM3
V+
Open
REF
BATT-
S10-S12
S12
–
S10
S11
Sense Voltage
(mV)
4
8
16
32
Table 8. Voltage Values
Voltage Value
VREF
VLIMIT
2.00
2.00
Function
Internal fixed reference voltage
Sets maximum charging voltage; R6 is
adjusted to set the level. Set VLIMIT to
VREF for normal operation.
High-temperature trip voltage. Fast charge
ceases when the TEMP pin exceeds this
voltage. R7 is adjusted to set the level.
Low-temperature trip voltage. Fast charge
will not start when the TEMP pin is below
this voltage. R8 is adjusted to set the level.
This voltage is 1/2 of VREF as long as the two
thermistors, TR1 and TR2, are at the same
temperature. A
Typical Operating
Characteristics
graph in the MAX712/MAX713
data sheet shows how this voltage will vary
with battery temperature. TR1 must be in con-
tact with the battery casing to sense the
battery temperature.
VTHI
1.33
Table 6. Factory Settings Before Shipment
Number of Cells
Timeout
ADC Interval
Fast-Charge Current
Trickle-Charge Current
Battery Temperature Rise Cutoff
V
LIMIT
2
264 minutes
168 seconds
250mA
32mA
+15°C
2.0V
VTLO
0.66
VTEMP
1.00
_______________________________________________________________________________________
5
Plik z chomika:
Kot_Maciek
Inne pliki z tego folderu:
0001.PDF
(10 KB)
1003.PDF
(374 KB)
1002.PDF
(139 KB)
1004.PDF
(342 KB)
1005.PDF
(170 KB)
Inne foldery tego chomika:
PDF2
PDF3
SPICE
Zgłoś jeśli
naruszono regulamin