1211.PDF

(33 KB) Pobierz
19-0416; Rev 0; 7/95
MAX866 Evaluation Kit
_______________General Description
The MAX866 evaluation kit (EV kit) is a fully assembled
and tested surface-mount printed circuit board. It can
also evaluate the adjustable-output MAX867.
The MAX866/MAX867 are CMOS, step-up, DC-DC
switching regulators for small, low input voltage or bat-
tery-powered systems. The MAX866 accepts a positive
input voltage between 0.8V and V
OUT
and converts it to
a higher, pin-selectable output voltage of 3.3V or 5V.
The MAX867 adjustable version accepts 0.8V to 6V
input voltages and generates a higher, adjustable out-
put voltage in the 2.7V to 6V range. Typical full-load effi-
ciencies for the MAX866/MAX867 are greater than 80%.
A movable jumper on the EV kit selects either a 3.3V or
5.0V output voltage. Additional pads on the board’s sol-
der side accommodate resistors for the LBI/LBO low
battery detector or MAX867 output adjustment.
____________________________Features
o
Low 0.8V to 6V Input Supply Voltage
o
0.9V Guaranteed Start-Up Supply Voltage
o
27µA Quiescent Current
o
1µA Shutdown Mode
o
Up to 250kHz Switching Frequency
o
±1.5% Reference Tolerance
o
Low-Battery Detector (LBI/LBO)
o
Ultra-Small 8-Pin µMAX Package (1.11mm High)
o
Surface-Mount Construction
o
Fully Assembled and Tested
Evaluates: MAX866/MAX867
____________________Component List
DESIGNATION
C1
QTY
1
DESCRIPTION
0.1µF ceramic capacitor
47µF, 16V, low-ESR tantalum
capacitors;
Sprague 593D476X0016D2W or
AVXTPSD476M016R0150
Open
330µH inductor;
CoilCraft D01608-334
20V, 500mA Schottky diode;
Motorola MBR0520LTI
MAX866CUA (8-pin µMAX)
3-pin headers
Shunts
PC board
MAX866 data sheet
______________Ordering Information
PART
MAX866EVKIT-MM
TEMP. RANGE
0°C to +70°C
BOARD TYPE
Surface Mount
C2, C3
2
_________________________Quick Start
The MAX866 EV kit is a fully assembled and tested sur-
face-mount board. Follow the steps below to verify
board operation.
Do not turn on the power supply
until all connections are completed.
1) Connect a 1.5V supply to the pad marked VIN. The
ground connects to the GND pad.
2) Connect a voltmeter and load (if any) to the VOUT
pad.
3) Place the shunt on J1 across pins 1 and 2.
4) Place the shunt on J2 across pins 1 and 2 for a 5V
output voltage, or across pins 2 and 3 for a 3.3V out-
put (input voltage less than 3.6V).
5) Turn on the power and verify that the output voltage is
5V.
6) Refer to the section
Evaluating the MAX867
to modify
the board for different output voltages.
R1, R2,
R3, R4, R5
L1
D1
U1
J1, J2
None
None
None
0
1
1
1
2
2
1
1
To contact Sprague, phone (603) 224-1961 or fax
(603) 224-1430. To contact Murata Erie, phone (404) 436-1300.
Refer to the MAX866/MAX867 data sheet for other component
suppliers’ phone numbers.
________________________________________________________________
Maxim Integrated Products
1
Call toll free 1-800-998-8800 for free samples or literature.
MAX866 Evaluation Kit
Evaluates: MAX866/MAX867
_______________Detailed Description
Input Source
In normal operation, the input source for the MAX866
evaluation board must be greater than 0.9V for start-up
and less than the output voltage plus 0.3V. A typical
input voltage range would be the 1.2V to 1.8V range of
a 1-cell NiCd battery. An input voltage greater than the
selected output voltage (but less than 7V) will not dam-
age the circuit. However, the MAX866 output will equal
the input voltage minus the 0.3V drop of the Schottky
diode, D1.
The input current depends on the power delivered to
the load. The following equations show how to calcu-
late the expected input current requirement.
Input Power = Output Power / Efficiency
and
Input Current = Input Power / Input Voltage
To calculate the input current for a typical operating cir-
cuit, assume a 2V input voltage, a 5V output voltage,
and a 5mA load. The expected efficiency can be taken
from the graphs on the MAX866/MAX867 data sheet.
Under the above conditions, the MAX866 delivers 85%
efficiency.
Input Power = (5.0V x 5mA) / 85%
Input Power = 29.41mW
and
Input Current = 29.41mW / 2.0V
Input Current = 14.71mA
Once started, the MAX866 actually operates from the
regulated output voltage. This means that the input
voltage can fall below the 0.9V minimum start-up volt-
age. Typically, the regulated output will be maintained
even if the input voltage drops to 0.5V. See the
Efficiency and Start-Up Voltage vs. Load Current
graphs in the
Typical Operating Characteristics
section
of the MAX866/MAX867 data sheet.
Jumper Selection
Two 3-pin headers select the shutdown mode and out-
put voltage. Table 1 lists the selectable jumper options.
Table 1. Jumper Selection
J1 Shunt J2 Shunt SHDN Pin
Location Location Connection
1&2
1&2
2&3
2&3
1&2
2&3
1&2
2&3
VOUT
VOUT
GND
GND
3V/5V Pin
Connection
GND
VOUT
GND
VOUT
MAX866
Output
5.0V
3.3V
VIN - 0.3V
VIN - 0.3V
Using the Low-Battery Indicator
The MAX866 has an additional comparator useful for
monitoring the input source’s voltage level. Resistor
locations R3 and R4 on the bottom of the printed circuit
board are connected as a voltage divider between the
LBI pad and the MAX866 LBI pin. Note that a printed
circuit board trace across R4 shorts the LBI pin to
ground when this function is not used. Cut the trace
before installing R4. Refer to the
Low-Battery Detection
section of the MAX866/MAX867 data sheet for instruc-
tions on selecting values for resistors R3 and R4.
Another location on the board facilitates the addition of
a pull-up resistor on the LBO output. LBO is an open-
drain output that can sink 2mA. Install resistor R5 if an
external circuit is to be driven from LBO.
2
_______________________________________________________________________________________
MAX866 Evaluation Kit
Evaluating the MAX867
The MAX866 EV kit can also evaluate the MAX867,
which generates output voltages in the 2.7V to 6.0V
range using external resistors. Besides replacing the
IC, the only other modifications required are to remove
the shunt on J2 and to add the output voltage-divider
resistors R1 and R2 (located on the board’s solder
side). The
Output Voltage Selection
section of the
MAX866/MAX867 data sheet gives instructions for cal-
culating R1 and R2 values.
Evaluates: MAX866/MAX867
VIN
R5
OPEN
1
SHDN
3
R1
OPEN
C2
47µF
16V
L1
330µH
LX 8
D1
MBRS0520
C3
47µF
16V
VOUT
2
J1
3
2
1
J2
R2
OPEN
1
SHDN
U1
2 3/5
3
C1
0.1µF
4
VREF
LBO
7
MAX866
GND
OUT
LBI
6
5
R3
OPEN
LBI
R4
0Ω
(SHORT)
LBO
Figure 1. MAX866 EV Kit Schematic
_______________________________________________________________________________________
3
MAX866 Evaluation Kit
Evaluates: MAX866/MAX867
Figure 2. MAX866 EV Kit Component Placement Guide—
Component Side
Figure 3. MAX866 EV Kit Component Placement Guide—
Solder Side
Figure 4. MAX866 EV Kit PC Board Layout—Component Side
Figure 5. MAX866 EV Kit PC Board Layout—Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
4
___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1995 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Zgłoś jeśli naruszono regulamin