KeyProx.pdf

(201 KB) Pobierz
Galaxy Keyprox
Installation and Programming Instructions
Card Self Learn Procedure....................................................................................... 5
Operation.................................................................................................................. 6
Dual Focus ........................................................................................................... 6
Door Control Programming...................................................................................... 7
Specifications ........................................................................................................... 8
Declaration of Conformance .................................................................................... 8
II1-0028 D
2
8/5/02
Compatibility
The Galaxy Keyprox is intended for use with the Galaxy 8, 18, 60, 128,
500, 504 and 512 panels. The panels must be fitted with software version
1.18 or later.
Most non encrypted HID* cards and standard ASK cards up to 34 Bit can
be read by the Keyprox. Proprietary card type may not be read properly by
the Keyprox
* Note
that some versions of the keypad may not have the HID functionality
enabled.
MAX cards or tags can be read by the Keyprox. However if MAX readers
are also used on the system, then the cards will needs to be programmed
on to two separate users, as they are seen in a different way by the MAX
type readers and the Keyprox.
Mounting
The Keyprox should be mounted on a flat vertical surface in a convenient
location. Separate the back plate from the rest of the keypad by gently
pushing on the two locking clips on the base of the Keyprox with a
screwdriver. Place the back plate on the wall at the desired location and
mark the position of the screw holes. Remove the plate then drill the holes
as required. The back plate can then be screwed to the wall while running
the cable connection through the available opening. Once the back plate
has been secured to the wall, the rest of the Keyprox can be clipped in
place by locating the top lugs first, then pushing the lower clips home,
gently but firmly.
II1-0028 D
3
8/5/02
The Keyprox is configured onto the Galaxy panel as two separate modules,
a keypad and a MAX reader. Before powering up the Keyprox, the address
must be set using the rotary switch on the back of the PCB. This address
will apply to both the Keypad and the MAX Reader sections. It is the
installer’s responsibility to ensure that the address set is compatible with
the system in use. Not all addresses are acceptable to all Galaxy panels.
Reference to the installation instructions of the Galaxy panel is
recommended.
Once the address has been set and the Keyprox has been powered up, it
must be configured onto the Galaxy system. This is done automatically on
leaving programming mode, or by repowering the system. When configured
correctly, the system will show that two modules have been added, a
keypad and a MAX reader, both with the same address.
Keypad Programming
The keypad side of the Keyprox requires no programming for most
installations. If required, the parameters for the keypad can be altered in
programming menu
58.
II1-0028 D
4
8/5/02
Card Self-Learn Procedure
Not all proximity cards and tags have the serial numbers printed on them.
However, the card number must be programmed into the Galaxy panel to
allow the card to work. To simply this programming process, a card self-
learn procedure has been included in the Keyprox.
Note:
The card self-learn procedure should only be used whilst the
Keyprox is in the user menu for entering the MAX card number and the
panel is waiting for the actual card number to be entered. Use of the self-
learn at other times will result in random menu selections.
Procedure
1.
Use the Keyprox to enter menu option 42.1. Select the user to
which the card is to be assigned. Within the user menu, select
option 7=MAX Number.
2.
Delete all the digits of the existing number using the B< button.
3.
Place the keypad in the Self-Learn mode by holding the A button
and pressing 1 button simultaneously. The keypad will give a
double beep to indicate entry into the Self-Learn mode.
4.
Within 3 seconds of the double beep, swipe the new card at the
Keyprox.
5.
The card number will appear one the keypad display.
6.
Press ENT to save the card number.
7.
To enter more cards, repeat the procedure for other users.
Note:
The Self-Learn mode will time out after 3 seconds if no card is
presented. During the Self-Learn mode operation, the keypad buttons will
not function.
II1-0028 D
5
8/5/02

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin