Updating Maps and Speed Cameras on SMEG.pdf

(1191 KB) Pobierz
Updating Maps and Speed Cameras on
SMEG+ Touchscreen Peugeot/Citroen
Introduction:
The following procedure was carried out on a 2014 Peugeot 308 fitted with a SMEG+ Touchscreen running
firmware SMEG5.2.C.R1. With that said the procedure is very likely similar for other firmware levels on the SMEG+.
I believe these maps may also work for the SMEG unit.
The icons I refer to later in the document are listed below:
Settings Icon
Sat Nav Icon
Second Screen Icon
To check the firmware and map level on your SMEG+, from any screen on the device press and hold the Settings
Icon for approximately 10 seconds. This will load a menu that shows you System Information including the System
Version and Map Version. See Screenshot below.
Table of Contents
Introduction:
........................................................................................................................................................
1
Sat Nav Map Updates:
..........................................................................................................................................
3
Preparing the USB Stick:
...................................................................................................................................
3
Retrieving your Activate Key.
............................................................................................................................
4
Installing the new maps on the SMEG+
..............................................................................................................
5
Speed Camera Updates:
.....................................................................................................................................
12
Preparing the USB Stick
..................................................................................................................................
12
Installing the Speed Camera Updates
..............................................................................................................
13
Links to download files
.......................................................................................................................................
15
Sat Nav Map Updates:
To begin with I would like to mention that the files that I installed in this guide were downloaded from GPS
underground. I will provide links to the files that I downloaded at the end of this guide, however depending on when
you are reading this, there are likely newer versions of the files available.
These map updates take around an Hour to install if you choose to install them all. Due to Peugeot ‘ECO’ Mode,
you will need to have the engine running to install the maps. You can drive the vehicle whilst the maps are
installing. Although some features like Volume control still work, access to the Touchscreen is very limited whilst
maps are being installed.
If you stop the engine whilst updating the maps. You will need to restart the installation process again using the
instructions below when you next switch the engine on (Unless you switch the engine back on before ECO mode
has stopped the process running in the background). You will notice that any Maps that have already been
completely installed, will not have a tick put next to them automatically, as they are already up to date, and you will
not have to install them again.
Preparing the USB Stick:
Insert a blank USB Stick (4GB or above) into your computer and Format it to FAT32.
I am not going to detail how to format the USB stick in FAT32. You can quickly find out how to do this using
Google, or a guide like this one:
http://www.wikihow.com/Format-FAT32
For reference I used an 8GB Transcend USB3 flash drive. I have seen comments on Forums that people have tried
and the process has failed. They have used a difference USB stick and it worked fine. If you run into issues during
the install, try a different USB before you change any other options.
Extract the files that you have downloaded and copy them to the root of the USB drive. The USB drive should
look like this when viewing it from Windows Explorer.
Retrieving your Activate Key.
To install the maps on the SMEG+ you need to insert an Activation Key. This can be done using the Key Generator
that is normally obtainable with the Maps that you download. Links will be provided at the end of the guide. Again,
there may be newer versions of this Keygen that will work with newer maps.
1) Extract the Keygen that you have downloaded and run the java file.
2) Insert your VIN number into the top box.
Click ‘Browse’ and Navigate to the USB stick, Navigate to the ‘SMEG_PLUS_UPG’ folder, then ‘Data’, select
the ‘CCT.DAT.INF’ file and click ‘Open’.
Note: Do not point the Keygen to the CCT.DAT.INF that is in the ROOT of the USB drive, or the code generated will
not work.
Make sure you point to \\USB\ \SMEG_PLUS_UPG\DATA\CCT.DAT.INF
I have not tried this, but I presume if you have the standard SMEG unit, you would point to the CCT.DAT.INF
in
\\USB\SMEG_PLUS\DATA\CCT.DAT.INF
My VIN and Activation code have been blurred out for Privacy
Reasons.
3) Click ‘Generate’. Your code will be generated in a popup box:
4) At this stage I would Print Screen this, and if possible print it out, and take it with you to the car.
Keep the code handy when you go to install the Maps on the SMEG+ as you will need to enter it quite early on in the
process.
Installing the new maps on the SMEG+
Press the Sat Nav icon to navigate to the Sat Nav Page.
Insert the USB stick into the CENTER console USB stick, not the one under the steering wheel.

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin