Montering.pdf

(981 KB) Pobierz
Teile und Zubehör - Einbauanleitung
F 46 0033 2W
Diebstahlwarnanlage (DWA)
für BMW 3er-Reihe (E 46/2/4) Linkslenker mit Funkfernbedienung ab Band
(Nur zum Gebrauch in der BMW HO bestimmt.)
Einbauzeit ca. 3,5 - 4,5 Stunden, die je nach Ausstattung des Fahrzeuges abweichen kann.
Elektrokenntnisse sind Voraussetzung.
BMW Parts and Accessories – Installation Instruction
Alarm system (DWA)
for BMW 3 Series (E 46/2/4) left-hand drive with remote control as standard
Instructions de montage des pièces et des accessoires BMW
Alarme antivol DWA
pour BMW Série 3 (E 46/2/4) avec commande à distance de série
BMW Onderdelen en accessoires – Montagehandleiding
Diefstalbeveiligingssysteem (DWA)
voor BMW 3-serie (E 46/2/4) linksgestuurd model met radiografische afstandsbediening vanaf fabriek
BMW Delar och tillbehör – Monteringsanvisning
Stöldlarm (DWA)
till BMW 3-serien (E 46/2/4), vänsterstyrd med fjärrkontroll som standardutrustning
Ricambi e accessori BMW – Istruzioni di montaggio
Antifurto con allarme acustico (DWA)
per BMW Serie 3 (E 46/2/4) guida a sinistra con telecomando di serie
BMW piezas y accesorios – instrucciones de montaje
Sistema de alarma antirrobo (DWA)
para BMW Serie 3 (E 46/2/4) con volante a la izquierda con mando a distancia de serie
Peças e Acessórios BMW – Instruções de Montagem
Alarme Anti-Roubo (DWA)
para os modelos BMW da Série 3 (E 46/2/4) de volante à esquerda com comando à distância de série
Best.-Nr. 01 29 0 004 369 II/99 Printed in Germany
1
Alarm system (DWA)
for BMW 3 Series (E 46/2/4) left-hand drive with remote control as standard
(Only for use within the BMW dealer organisation).
Fitting time approx. 3.5 to 4.5 hours, depending on
the condition of and equipment in the car.
Electrical skills are required.
Contents
Section
1. Preparatory work on the car
2. Installation and cabling diagram
3. Connection diagram for the alarm system
wiring harness
4. To connect the alarm system wiring harness
5. To install the engine compartment contact
6. To install the emergency-current siren
7. To install the LED
8. To install the ultrasonic module
9. To install the tilt alarm sensor
10. To connect the boot lid lock switch
11. Coding
12. Function test
13. Troubleshooting chart
14. Wiring diagram for E 46 alarm system
General notes
Tie back excess length cables.
Seal cable passage to the engine compartment
with the appropriate sealing compound.
If the specific pins or joint connectors are already
in use, bridges, double crimps or parallel stops
must be fitted.
Drilling instructions
Deburr drilled holes and treat them with the
anti-corrosive prescribed by BMW. Remove
all drill chippings.
Ordering instructions
The cover for the ultrasonic module must be
ordered separately to match the interior trim
colour (see ETK for part numbers).
For cars from the start of this Series up to and
including 9/99
which have a free slot in the switch
strip,
the LED with part No. 65 75 8 357 417 may
be installed as an option
(see section 7, page 9).
1. Preparatory work on the car
-
-
-
Print out the error memory
Disconnect the battery,
on models with a
battery in the engine compartment, remove
the battery
Remove the microfilter and engine
compartment bulkhead to the heater/air
conditioning unit
Remove the trim in the footwell on the
right-hand side
Remove the glove box
Release the fuse box and the module holder
Remove the switch trim and oddments tray
in the centre console
Remove the A, B and C pillar trims on the
right-hand side
Remove the grab handles and sun visors
on the right-hand side
Remove the door sill strips on the
right-hand side
Remove the rear seat bench and backrest
Remove the trim in the boot on the
right-hand side
Remove the boot lid trim
As a result of the continuous revision of the
electrical system on the various models, it is
possible that plug connectors (those with an X
identifier) or cable colours may change. Therefore
the latest version of the test instructions must be
used to fit the alarm system.
Ensure that the cables are not kinked or damaged
when they are installed in the car since otherwise,
this too may cause faults which then require a
great deal of work for their localisation. The costs
incurred as a result of this will not be reimbursed
by BMW.
Tools and equipment required
Philips screwdriver
Straight slot screwdriver
1/4 inch reversible ratchet
1/4 inch sockets, sizes 8 mm, 10 mm and 13 mm
1/4 inch extension
Side cutter
Torx wrench set
Centrepunch
Hammer
Torch
Sealing compound
Universal lubricating spray
Pencil
Carpet knife
Drill
Drill bits, sizes 3.5 mm, 5.5 mm and 8.0 mm
Tape measure
-
-
-
-
-
-
-
-
-
-
2. Installation and cabling diagram
F 46 0034 2W
Legend
Connector for fuse box and base module
Bonnet contact
Emergency-current siren
LED (only cars from the start of this Series up
to and including 8/99 which have a free slot in
the switch strip, see ordering instructions on
page 2)
4a LED
5. Ultrasonic module
6. Tilt alarm sensor
7. Boot lid lock switch
1.
2.
3.
4.
17
3. Connection diagram for the alarm system wiring harness
F 46 82 029 R
Item
A
B
B1
C1
C2
C3
C4
C5
C6
C7
D
E
F
G
G1
G2
G3
Description
Signal
Cable
colour
Cable
Connection location in the car
cross-section
0.75 mm
2
2.5 mm
2
–––––
0.35 mm
2
0.50 mm
2
0.75 mm
2
0.50 mm
2
0.50 mm
2
0.50 mm
2
0.50 mm
2
–––––
0.35 mm
2
–––––
–––––
0.75 mm
2
0.50 mm
2
0.75 mm
2
At fuse box
A46,
pin 30, slot No. F67
Joint connector, X219, behind the glove box
Joint connect box behind the glove box
On the base module, black 26-pin
plug X254, pin 10
On the base module, black 26-pin
plug X254, pin 7
On the base module, black 26-pin
plug X254, pin 8
On the base module, black 26-pin
plug X254, pin 24
On the base module, black 26-pin
plug X254, pin 23
On the base module, black 26-pin
plug X254, pin 6
On the base module, black 26-pin
plug X254, pin 5
On tilt alarm sensor, plug X1222
On boot lid lock switch, black 3-pin
plug X1191, pin 3
On ultrasonic module, plug X1582
On the emergency-current siren, plug X372
On the emergency-current siren, black 4-pin
plug X372, pin 1
On the emergency-current siren, black 4-pin
plug X372, pin 2
On the emergency-current siren, black 4-pin
plug X372, pin 3
Terminal 30
Blade terminal contact
red/black
Terminal 31
Joint terminal contact
brown
Joint terminal casing
–––––
Boot
Blade terminal contact
brown/blue
(boot lid switch)
Engine
Blade terminal contact
violet/green
(engine compartment contact) compartment
Alarm/Siren
Blade terminal contact
black/blue
(emergency-current siren)
Alarm/
Blade terminal contact
black/yellow
U.module
(ultrasonic module)
LED/on
Blade terminal contact
grey/black/
(LED)
yellow
Alarm/
Blade terminal contact
black/blue/
tilt sensor
(tilt sensor)
yellow
DWA/on
Blade terminal contact
black/red
(DWA arming)
–––––
6-pin black socket casing
–––––
Blade terminal contact
(boot lid switch)
4-pin black socket casing
4-pin black socket casing
Blade terminal contact
(emergency-current siren)
Blade terminal contact
(emergency-current siren)
Blade terminal contact
(emergency-current siren)
Boot
–––––
–––––
Terminal 31
Siren/on
Terminal 30
brown/blue
–––––
–––––
brown
black/red
red/black
Item
G4
H
I
I1
I2
Description
Blade terminal contact
(emergency-current siren)
4-pin black socket casing
3-pin black socket casing
Signal
Alarm/
on
–––––
–––––
Cable
colour
black/blue
–––––
–––––
brown
violet/green
Cable
cross-section
0.75 mm
2
–––––
–––––
0.50 mm
2
0.50 mm
2
Connection location in the car
On the emergency-current siren,
black 4-pin plug X372, pin 4
On the LED, plug X514
On the engine compartment contact,
plug X161
On the engine compartment contact,
black 3-pin plug X161, pin 1
On the engine compartment contact,
black 3-pin plug X161, pin 2
Terminal 31
Blade terminal contact
(engine compartment contact)
Engine
Blade terminal contact
(engine compartment contact) compartment
18
4. To connect the alarm system
wiring harness
F 46 82 030 R
Release the fuse box
A46
(3). Undo the Torx
screws (1) on the fuse box
A46
(3). Release the
catches in the recesses (2) using a small straight
slot screwdriver and take out the fuse box
A46
(3)
in the direction indicated by the arrow.
C5
Connect the blade terminal contact (LED),
grey/black/yellow cable, to pin 23.
Connect the blade terminal contact (tilt
alarm sensor), black/blue/yellow cable,
to pin 6.
Connect the blade terminal contact (DWA
arming), black/red cable, to pin 5.
C6
C7
Connection to the black 4-pin plug X372
F 46 82 034 R
Push branches
G1-G4
(2) through the rubber
grommet (1) behind the fuse box
A46
(3).
Fit branches
G1-G4
into plug casing
G
as follows:
G1
Connect the blade terminal contact
(emergency-current siren) terminal 31,
brown cable, to the enclosed 4-pin black
plug X372, pin 1.
Connect the blade terminal contact
(emergency-current siren) emergency-
current siren/on, black/red cable, to the
enclosed 4-pin black plug X372, pin 2.
Connect the blade terminal contact
(emergency-current siren) terminal 30,
red/black cable, to the enclosed 4-pin
black plug X372, pin 3.
Connect the blade terminal contact
(emergency-current siren) alarm/on,
black/blue cable, to the enclosed 4-pin
black plug X372, pin 4.
When the fuse box
A46
(3) is removed, the
blade terminal fuses in the bottom row of slots
will drop out.
When the fuse box
A46
is reinstalled ensure that
all the blade terminal fuses are replaced in their
correct positions.
F 46 82 031 R
A
Connect blade terminal 30 (1), red/black
cable, to the fuse strip (2), slot No.
F67,
as
shown. Reinstall the fuse box
A46
following
the above instructions in reverse. Fit the 5 A
blade terminal fuse in slot No.
F67.
G2
The cable from branch
A
terminal 30 (1) must
not be fitted under tension. Depending on the
equipment in the car, it may be that slot No.
F67
is already in use. In this case branch
A
must be
connected to the free slot above used slot
No.
F67.
F 46 82 032 R
B
Connect terminal 31 branch (1), brown cable,
to joint connector X219 (2). Insert the joint
connector casing
B1
into the joint connector
box.
G3
G4
Make very sure that you do get branches
G2
and
G3
mixed up.
Connection to the black 3-pin plug X161 (3)
F 46 82 035 R
Push branches
I1
and
I2
(1) through the rubber
grommet (2) beneath the battery plate into the
engine compartment.
I1
Connect the blade terminal contact
(engine compartment contact) terminal 31,
brown cable, to the enclosed 3-pin black
plug X161 (3), pin 1.
Connect the blade terminal contact
(engine compartment contact) alarm/on,
violet/green cable, to the enclosed 3-pin
black plug X161 (3), pin 2.
Connection to base module
F 46 82 033 R
Disconnect plugs (1, 2 and 3) from the GM module.
Depending on the equipment in the car, it may
be that the black 26-pin plug X254 (3) is not fitted.
In this case use the plug supplied in the installation
kit.
Connection to the black 26-pin plug X254 (3)
C1
Connect the blade terminal contact (boot lid
lock switch), brown/blue cable, to pin 10.
Connect the blade terminal contact (engine
compartment contact), violet/green cable,
to pin 7.
Connect the blade terminal contact
(emergency-current siren), black/blue cable,
to pin 8.
Connect the blade terminal contact
(ultrasonic module), black/yellow cable,
to pin 24.
I2
C2
C3
5. To install the engine
compartment contact
F 46 82 036 R
Fit the engine compartment contact (1) into the
recess in the external jump starting support (3)
provided for it. Connect branch
I,
plug X161 (2)
to the engine compartment contact (1).
C4
19
6. To install the emergency-current
siren
Cars from the start of the Series to 3/99 only
F 46 82 037 R
Mark dimensions
A
and
B
on the holder (2) as
shown. Centrepunch the marked point and drill
through it using a 5.5 mm drill bit.
Dimensions:
A
= 26 mm
B
= 30 mm
Deburr drilled holes and treat them with the
anti-corrosive prescribed by BMW. Remove all drill
chippings.
Bolt the emergency-current siren (1) to the holder (2)
using the hexagonal nut, size M6 (3).
F 46 82 038 R
Hold the emergency-current siren (1) and the holder
on the car next to the heater/air conditioning unit (2).
Mark the hole on the car, centrepunch the marked
point (3) and drill through it using a 3.5 mm drill bit.
Deburr drilled holes and treat them with the
anti-corrosive prescribed by BMW. Remove all drill
chippings.
F 46 82 039 R
Secure the holder for the emergency-current
siren (1) using the enclosed hexagonal self-tapping
screw (2). Connect branch
G,
plug X372 (3) to the
emergency-current siren (1).
Cars after 4/99 only
F 46 0021 2W
Secure the emergency-current siren (1) to the
holder (2) using the hexagonal nut, size M6 (3).
F 46 0023 2W
Insert the Prestol cage (1) into the square hole on
the car as shown.
F 46 0022 2W
Secure the emergency-current siren (1) to the
Prestol cage using the enclosed hexagonal screw,
size M6 (2). Connect branch
G,
plug X372 (3) to
the emergency-current siren (1).
LED (2) in the switch strip. Cut the switch
trim to suit the car's equipment and refit it.
The LED for installation in the switch strip is
not supplied in the installation kit (see ordering
instructions on page 2).
Cars without a free slot in the switch strip and
cars from 9/99 with a switch centre only
F 46 0031 2W
Mark dimensions
A
and
B
on the centre console (1)
as shown. Centrepunch the marked position and
carefully drill and deburr a hole with a 8.0 mm drill
bit.
Dimensions:
A
= 83 mm
B
= 23 mm
F 46 0032 2W
Insert the LED (1), if necessary slightly enlarge the
hole.
Connect the LED (1) cables, red/black cable to pin
1 of the enclosed 4-pin black plug casing. Connect
the grey/black/yellow cable to pin 4 of the 4-pin
black plug casing.
Lay branch
H,
black 4-pin plug X514 to the centre
console.
Connect branch
H
to the connector for the LED (1).
8. To install the ultrasonic module
Cars without a slide/tilt sunroof only
F 46 82 041 R
When affixing the template (1), it must be
ensured that the template (1) is affixed in the
centre.
Affix the template (1) as shown in the centre of the
head liner (2). Cut out the section with a sharp
carpet knife.
Cars with a slide/tilt sunroof only
F 46 82 042 R
When affixing the template (1), it must be
ensured that the template (1) is affixed in the
centre.
Affix the template (1) as shown in the centre of the
head liner (2). Cut out the section with a sharp
carpet knife.
7 To install the LED
.
Cars from the start of the Series up to and
including 8/99 with a free slot in the switch
strip only
F 46 82 048 R
To prevent faults on the ITS head airbags,
branch F must be fitted as shown along the
route provided for it as standard.
F 46 0025 2W
H
Lay the black 4-pin plug X514 (1) to a free
slot in the switch strip on the centre console.
Connect branch
H
(1) to the LED (2). Fit the
Clip the cables from plug
F
(1) on the right-hand
A pillar into the existing wiring harness holders.
20

Plik z chomika:

Inne pliki z tego folderu:

Inne foldery tego chomika:

Zgłoś jeśli naruszono regulamin